View DOM40S6V15G_1138373.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

hanbit hfdom40s6vxxx url:www.hbe.co.kr - 7 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) 1. product overview general description the hfdom40s6vxxx series 40pin flash disk module is a flash technology based with true ide interface flash memory card. it is constructed with flash disk controlle r chip and nand-type (samsung) flash memory device. the hfdom40s3v-xxx series operates in both 3.3-volt and 5.0-volt power supplies. it comes in capacity of 128,256,384,512,640,768,1g,1.5g,2 gand up to 3gbyte formatted 40pin type . by optimizing flash memory management, the life of this hfdom40s6vxxx series can be extended to its maximum level. because the ecc function is included, the correctness of data transfer between the hfdom40s6vxxx series and a true ide compatible interfac e device can be guaranteed. the hfdom40s6vxxx series is fully compatible with applic ations such as cpu card / board, set top box, industry / military pc / notebook, security equipmen t, measuring instrument and embedded systems. features - ata / true ide compatible host interface - ata command set compatible - automatic sensing of pc card ata or true ide host interface. - very high performance, very low power consumption - automatic error correction - auto standby to save power consumption. - supports power down commands and sleep modes. - integrated pcmcia attribute memory of 256 bytes (cis) - support for 8 or 16 bit host transfers - 3.3v/5.0v operation voltage - host interface bus width : 8/16 bit access - flash interface bus width : 8 bit access - capacity : min. 128mb ~ max. 3gb - mtbf > 1,000,000 hours. - minimum 10,000 insertions. - shock : 2,000 g max. - vibration : 15 g peak to peak max. product specifications capacities : 128,256,384,512,640,768, 1g,1.5g,2gand up to 3gb (formatted) system compatibility : please refer to the compatibility list of index. performance : host data transfer rates : up to 16.6 mb/sec, pio mode 4; 16.6mb/sec 40pin flash disk module min.128mb ~ max.3gb, true ide interface
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 8 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) operating voltage : 3.3v / 5.0v 10% power consumption : 3.3v 5% read mode <30 ma write mode <56 ma stop mode <2 ma environment conditions : operating temperature 0c to + 70c storage temperature - c to + c relative humidity 8% to 95%, non-condensing electrical specifications table 1.1 absolute maximum ratings symbol parameter rating units v dd power supply -0.3 to 3.6 v v in input voltage -0.3 to v dd +0.3 v v out output voltage -0.3 to v dd +0.3 v t stg storage temperature -55 to 150 o c table 1.2 recommended operating conditions symbol parameter min. max. units v dd power supply 3.0 3.6 v v in input voltage -0.3 v dd +0.3 v t opr operating temperature 0 70 o c table 1.3 dc characteristics sym. parameter min typ max units v il input low voltage 0.3v dd v v ih input high voltage 0.7v dd v v il schmitt input low voltage 1.22 v v ih schmitt input high voltage 2.08 v v ol output low voltage 0.4 v v oh output high voltage 2.3 1 v r i input pull up/down resistance 75 k ?
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 9 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) physycal specification
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 10 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) installtion guide 1) setting method make sure your computer is turned off before you open the case. plug the carefully into the 40pin ide slot on your computer. caution: make sure to align pin1 on host adapter interface c onnector with pin 1 on your flash disk module. pin 1 is indicated by a triangle on the flash disk module connector. the flash disk module is used power connector cable of the computer. caution: if you need to remove your flash disk module, use both hands to pull it out carefully. check all cable connections and then replace your computer cover. 2) bios setting method before you format or partition your new drive, you must c onfigure your computer's bios so that the computer can recognize your new drive. turn your computer on. as your computer start up, watch the screen for a message describing how to run the system setup program on the screen (som etimes called bios or cmos setup). this is usually done by pressing a special key, such as delete , esc or f1 during startup. see your computer m anual for details. press the appropriate key to run the system setup program. if your bios provides automatic drive detecti on (an "auto" drive type), select this option. ( we recommend to use normal / chs mode to partition your flash disk module to get the maximum formatted capacity. ) this allows your computer to configure itself automatically for your new drive. if your bios dose not provide ?aut o? drive detection, select "user-d efined" drive setting and enter the chs values from the table. bios settings (see specification) capac ity cylinders heads sectors(unformatted) save the settings and exit the syst em setup program. ( your computer will automatically reboot ) after you configure your computer, you can us e the standard dos commands to partiti on and format your flash disk module, as described below. 3) formatting method to partition your new flash disk module with microsoft dos program : insert a bootable dos diskette into your diskette drive and restart your computer. insert a dos program diske tte that contains the fdisk.exe and format.com programs into your diskette drive. use the same do s version that is on your bootable diskette. at the a:\ > prompt, type ?fdisk? and press enter . select ?create dos partition or logical dos drive? by pressing 1 . then press enter . select ?create primary dos partition? by pressing 1 again. then press enter . create your first drive partition. if you are creating a parti tion that will be used to boot your computer (drive c), make sure that the partition is marked active. create an extended partition and additional l ogical drives as necessary, until a ll the space on your new hard drive has been partitioned. when the partitioning is complete, fdisk reboots your computer. caution: make sure to use the correct driv e letters so that you do not format a drive that already contains data. at the a:\ > prompt, type ?format c:/s? , where c is the letter of your first new partition, repeat the format process for all the new partitions you have created. after you format your drive, it is ready to use.
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 11 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) 2. pin information pin assignments and pin type table 2.1 pin assignment and pin type pin signal pin type pin signal pin type 1 /reset i 2 gnd ground 3 d07 i/o 4 d08 i/o 5 d06 i/o 6 d09 i/o 7 d05 i/o 8 d10 i/o 9 d04 i/o 10 d11 i/o 11 d03 i/o 12 d12 i/o 13 d02 i/o 14 d13 i/o 15 d01 i/o 16 d14 i/o 17 d00 i/o 18 d15 i/o 19 gnd dc 20 key pin -- 21 inpack -- 22 gnd ground 23 /iow i 24 gnd ground 25 /ior i 26 gnd ground 27 iordy o 28 reserved -- 29 reg -- 30 gnd ground 31 irq o 32 /iois16 o 33 a01 i 34 /pdiag i/o 35 a00 i 36 a02 i 37 /cs0 i 38 /cs1 i 39 /dasp i/o 40 gnd ground
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 12 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) signal descriptions table 2.2 signal descriptions signal name dir. pin description a[2:0] i 33,35,36 in true ide mode only a[2:0] are used to select the one of ei ght registers in the task file, the remaining address lines should be grounded by the host. -pdiag i/o 34 this input / output is the pass diagnos tic signal in the master / slave handshake protocol. -dasp i/o 39 in the true ide mode, this input/ output is the disk active/slave present signal in the mast er/slave handshake protocol. -cs0, -cs1 i 37,38 cs0 is the chip select for the task file registers while cs2 is used to select the alternate status register and the device control register. d[15:00] i/o 3,4,5,6, 7,8,9,10, 11,12,13, 14,15,16, 17,18 all task file operations occur in by te mode on the low order bus d00-d07 while all data transfers are 16 bit using d00-d15. gnd -- 2,19,22, 24,26, 30,40, ground. -ior i 25 this is an i/o read strobe generated by the host. -iow i 23 the i/o write strobe pulse is used to clock i/o data on the card data bus into the storage card controller r egisters when the storage card is configured to use the i/o interface. t he clocking will occur on the negative to positive edge of the signal (trailing edge). irq o 31 in true ide mode signal is the active high interrupt request to the host. -reset i 1 this input pin is the active low hardware reset from the host. iordy o 27 this output signal may be used as iordy. -iois16 o 32 this output signal is asserted low when this device is expecting a word data transfer cycle.
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 13 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) block diagram figure 2.1 block diagram 3. interface bus timing access spcifications 1 system clock timing sym. description min. typ. max. unit tc clock cycle time 45 50 100 ns tlpd clock low pulse duration 0.4tc 0.6tc ns thpd clock high pulse duration 0.4tc 0.6tc ns tlpd thpd tc pcmcia ata interface 8032 micom ata interface ram rom code buffer management and control ecc circuit flash sequencer and control logic nand flash device nand flash device nand flash device host interface
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 14 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) 2 host read/write timing sym. description min. typ. max. unit td hd bus asserted from hior# / hoe# 10 ns th (r) hd hold time after hior# / hoe# 40 70 ns ts (w) hd set up time of hiow# / hwe# 10 ns th (w) hd hold time of hiow# / hwe# 5 ns read hd valid td th (r) hd write th (w) ts (w) hiow#/ hwe# hior#/hoe# ha ha valid ce[2:1] 3 flash read/write timing sym. description min. typ. max. unit tc (f) flash read / write cycle time 100 ns ts (fw) fd set up time of fwe# 80 ns th (fw) fd hold time of fwe# 40 ns ts (fr) fd set up time of frd# 10 ns th (fr) fd hold time of frd# 5 ns
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 15 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) registers 1) data register (address ? 1f0h[170h];offset 0,8,9) the data register is a 16-bit register, and it is used to transfer data blocks between the compactflash storage card data buffer and the host. this register overlaps the erro r register.the table below describes the combinations of data register access and is provided to a ssist in understanding the overlapped data register and error/feature register ra ther than to attempt to define general pcmcia word and byte access modes and operations. see the pcmcia pc card standard release 2.0 for definitions of the card accessing modes for i/o and memory cycles. note: because of the overlapped regi sters, access to the 1f1h, 171h or offset 1 are not defined for word (-ce2 = 0 and -ce1 = 0) operations. these accesses ar e treated as accesses to the word data register. the duplicated registers at offsets 8, 9 and dh have no rest rictions on the operations that can be performed by the socket. data register access data register ce2- ce1- a0 offset data bus word data register 0 0 x 0,8,9 d15-d0 even data register 1 0 0 0,8 d7-d0 odd data register 1 0 1 9 d7-d0 odd data register 0 1 x 8,9 d15-d8 error/feature register 1 0 1 1,dh d7-d0 error/feature regist er 0 1 x 1 d15-d8 error/feature register 0 0 x dh d15-d8 2) error regis t er (address ? 1f1h[171h];offset 1,0dh read only) this register contains additional information about the source of an error when an error is indicated in bit 0 of the status regist er. the bits are defined as follows: d7 d6 d5 d4 d3 d2 d1 d0 bbk unc 0 idnf 0 abrt 0 amnf error register this register is also accessed on data bits d15-d8 during a write operation to offset 0 with -ce2 low and -ce1 high. bit 7 (bbk ): this bit is set when a bad block is detected. bit 6 (unc ): this bit is set when an uncorrectable error is encountered. bit 5: this bit is 0. bit 4 (idnf ): the requested sector id is not valid error or cannot be found. bit 3: this bit is 0. bit 2 (abort) this bit is set if the command has been aborted because of a compactflash storage card status condition: (not ready, write fault, etc.) or when an invalid command has been issued. bit 1 this bit is 0. bit 0 (amnf) this bit is set in case of a general error happened. 3) feature register(address ? 1f1h[171h];offset 1,0dh writer only) this register provides information r egarding features of the compactflash storage card that the host can utilize. this register is also accessed on data bits d15-d8 during a write operation to offset 0 with -ce2 low and -ce1 high. bit description- 7 6 5 4 3 2 1 0 command specific 4) sector count register(a ddress ? 1f2h[172h];offset 2)
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 16 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) this register contains the num bers of sectors of data request ed to be transferred on a read or write operation between the host and the compactflash storage card. if the val ue in this register is zero, a count of 256 sectors is specified. if the co mmand was successful, this register is zero at command completion. if not successfully completed, the register contains the number of sectors t hat need to be transferred in order to complete the request. bit description- 7 6 5 4 3 2 1 0 sector count 5) sector number (lba 7-0) register(address?1f3h[173h];offset 3) this register contains the star ting sector number or bits 7-0 of the logical block address (lba) for any compactflash storage card data access for the subsequent command. bit description - chs 7 6 5 4 3 2 1 0 sector (7: 0) lba 7 6 5 4 3 2 1 0 lba (7 : 0) 6) cylinder low (lba 15-8 )register (address?1f4h[174h];offset 4) this register contains the low order 8 bits of the starting cylinder addre ss or bits 15-8 of the logical block address. dit description- chs 7 6 5 4 3 2 1 0 cylinder ( 7: 0 ) lba 7 6 5 4 3 2 1 0 lba ( 15 : 8 ) 7) cylinder high(lba 23?16)regist er(address?1f5h[175h]; offset 6) this register contains the high order bits of the starting cyli nder address or bits 23-16 of the logical block address. bit description- chs 7 6 5 4 3 2 1 0 cylinder ( 15 :8 ) lba 7 6 5 4 3 2 1 0 lba ( 23 : 16 ) 8) status / alternate status register (address 1f7h[177h]/3f6h[376h];offset 7/ eh) these registers return the compactflash st orage card status when read by the host. reading the status register does cl ear a pending interrupt, while reading the alter nate status register does not. the status bits are described as follows:
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 17 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) d7 d6 d5 d4 d3 d2 d1 d0 busy rdy dwf dsc drq corr 0 err status & alternate status register bit 7 (busy ): the busy bit is set when the compac tflash storage card has access to the command buffer and registers and the host is locked out from accessing the command register and buffer. no other bits in this regi ster are valid when this bit is set to a 1. bit 6 (drdy ): drdy indicates whether the device is c apable of performing compactflash storage card operations. this bit is cleared at power up and remains cl eared until the compactflash storage card is ready to accept a command. bit 5 (dwf ): this bit, if set, indicates a write fault has occurred. bit 4 (dsc ): this bit is set when the compactflash storage card is ready. bit 3 (drq ): the data request is set when the co mpactflash storage card requires the information to be transferred either to or from the host through the data register. bit 2 (corr ): this bit is set when a correctable data e rror has been encountered and t he data has been corrected. this condition does not terminate a multi-sector read operation. bit 1 (idx ): this bit is always set to 0. bit 0 (err ): this bit is set when the previous command has ended in some type of error. the bits in the error register contain additional information describing the error. it is recommended that media access commands (such as read se ctors and write sectors) that end with an error condition should have the address of the fi rst sector in error in the command block registers. 9) device control register( address ? 3f6h[376h]; offset eh) this register is used to control t he compactflash storage card interrupt request and to issue an ata soft reset to the card. this register can be written even if t he device is busy. the bits are defined as follows: d& d6 d5 d4 d3 d2 d1 d0 x x x x 1 sw rst -ien 0 device control register bit 7: this bit is an x (don?t care). bit 6: this bit is an x (don?t care). bit 5: this bit is an x (don?t care). bit 4: this bit is an x (don?t care). bit 3: this bit is ignored by the compactflash storage card. bit 2 (sw rst ): this bit is set to 1 in order to force t he compactflash storage card to perform an at disk controller soft reset operation. this does not change the pcmcia card configuration registers (4.3.2 to 4.3.5) as a hardware reset does. the card remains in reset until this bit is reset to ?0.? bit 1 (-ien ): the interrupt enable bit enables interrupt s when the bit is 0. when the bit is 1, the interrupts from the compactflash storage card are disabled. this bit also controls the int bit in the configuration and status r egister. this bit is set to 0 at power on and reset. bit 0 : this bit is ignored by the compactflash storage card. 10) card (drive) address register(address 3f7h[377h]; offset fh) this register is provided for compatib ility with the at disk drive interface. it is recommended that this register not be mapped into the host?s i/o space becaus e of potential conflicts on bit 7. the bits are defined as follows: d7 d6 d5 d4 d3 d2 d1 d0 x -wtg -hs3 -hs2 -hs1 -hs0 -nds1 -nds0 card (drive) address register bit 7: this bit is in high imoedence..
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 18 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) implementation note: conflicts may occur on the host data bus when this bit is provided by a floppy disk controller operating at the same addresses as the com pactflash storage card. following are some possible solutions to this problem for the pcmcia implementation: 1) locate the compactflash storage card at a non-conflicting addr ess, i.e. secondary address (377) or in an independently decoded addr ess space when a floppy disk controller is located at the primary addresses. 2) do not install a floppy and a compactflash st orage card in the system at the same time. 3) implement a socket adapter, which can be progr ammed to (conditionally) tri-state d7 of i/0 address 3f7h/377h when a compact flash storage card is installed and conversely to tri-state d6-d0 of i/o address 3f7h/377h when a fl oppy controller is installed. 4) do not use the compactflash storage ca rd?s drive address register. this may be accomplished by either a) if possible, progr am the host adapter to enable only i/o addresses 1f0h-1f7h, 3f6h (or 170h-177h, 176h) to the compac tflash storage card or b) if provided use an additional primary / secondary configur ation in the compactflash storage card which does not respond to accesses to i/o loca tions 3f7h and 377h. with either of these implementations, the host software must not atte mpt to use information in the drive address register. bit 6 (-wtg ): this bit is 0 when a write operation is in progress, otherwise, it is 1. bit 5 (-hs3 ): this bit is the negation of bi t 3 in the drive/head register. bit 4 (-hs2 ): this bit is the negation of bi t 2 in the drive/head register. bit 3 (-hs1 ): this bit is the negation of bi t 1 in the drive/head register. bit 2 (-hs0 ): this bit is the negation of bi t 0 in the drive/head register. bit 1 (-nds1 ): this bit is 0 when drive 1 is active and selected. bit 0 (-nds0 ): this bit is 0 when the dr ive 0 is active and selected. 4. ata command cf-ata command set table summarizes the cf-ata command set with the paragraphs that follow describing the individual commands and the task file for each. table:cf-ata command set class command code fr sc sn cy dh lba 1 check power mode e5h or 98h - - - - d - 1 execute drive diagnostic 90h - - - - d - 2 format track 50h - y - y y y 1 identify drive ech - - - - d - 1 idle e3h or 97h - y - - d - 1 idel immediate e1h or 95h - - - - d - 1 initialize drive parameters 91h - y - - y - 1 read buffer e4h - - - - d - 1 read long sector 22h or 23h - - y y y y 1 read multiple c4h - y y y y y 1 read sector(s) 20h or 21h - y y y y y 1 read verify sector(s) 40h or 41h - y y y y y 1 recalibrate 1xh - - - - d - 1 request sence 03h - - - - d - 1 seek 7xh - - y y y y 1 set features efh y - - - d - 1 set multiple mode c6h - y - - d -
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 19 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) 1 set sleep mode e6h or 99h - - - - d - 1 stand by e2h or 96h - - - - d - 1 stand by immediate e0h or 94h - - - - d - 1 translate sector 87h - y y y y y 1 wear level f5h - - - - y - 2 write buffer e8h - - - -- d - 2 write long sector 32h or 33h - - y y y y 3 write multiple c5h - y y y y y 3 writemultiple w/o erase cdh - y y y y y 2 write sector(s) 30h or 31h - y y y y y 2 write sector(s) w/o erase 38h - y y y y y 3 write verify 3ch - y y y y y definitions: -- fr = features register -- sc = sector count register -- sn = sector number register -- cy = cylinder registers -- dh = card/drive/head register -- lba = logical block address mode supported (see command descriptions for use). -- y - the register contains a valid parameter fo r this command. for the drive/head register y means both the compactflash st orage card and head parameters are us ed; d - only the compactflash storage card parameter is va lid and not the head parameter. check power mode ? 98h or e5h bit-> 7 6 5 4 3 2 1 0 command(7) 98h or e5h c/d/h(6) x drive x cly high(5) x cly low(4) x sec num(3) x sec cnt(2) x feature(1) x check power mode this command checks the power mode. f the compactflash storage card is in, going to, or recovering from the sleep mode, the compactflash storage card se ts bsy, sets the sector count register to 00h, clears bsy and generates an interrupt. if the compac tflash storage card is in idle mode, the compactflash storage card sets bsy, sets t he sector count register to ffh, clears bsy and generates an interrupt. execute drive diagnostic ? 90h bit-> 7 6 5 4 3 2 1 0 command(7) 90h c/d/h(6) x drive x
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 20 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) x feature(1) x execute drive diagnostic this command performs the internal diagnostic test s implemented by the compactflash storage card. if in pcmcia configuration this command runs only on t he compactflash storage card which is addressed by the drive/head register when the diagnosti c command is issued. this is becaus e pcmcia card interface does not allows for direct inter-drive communication (such as the ata pdiag and dasp signals). if in true ide mode the drive bit is ignored and the diagnostic command is executed by both the mast er and the slave with the master responding with status for both devices. the diagnostic codes shown in table 39 are returned in the error register at the end of the command. diagnostic codes code error type 01h no error detected 02h formatter device error 03h sector buffer error 04h ecc circuitry error 05h controlling microprocessor error 8xh slave error in true ide mode erase sector(s) ? c0h bit-> 7 6 5 4 3 2 1 0 command(7) c0h c/d/h(6) 1 lba 1 drive head(lba 27-24) cyl high(5) cylinder high (lba 23-16) cyl low(4) cylinder low (lba 15-8) sec num(3) sector number (lba 7-0 ) sec cnt(2) sector count feature(1) x erase sector this command is used to pre-erase and condition data sectors in advance of a write without erase or write multiple without erase command. there is no data transfer associated with this command but a write fault error status can occur. format track - 50h bit-> 7 6 5 4 3 2 1 0 command(7) 50h
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 21 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) c/d/h(6) 1 lba 1 drive head(lba 27-24) cyl high(5) cylinder high (lba 23-16) cyl low(4) cylinder low (lba 15-8) sec num(3) x (lba 7-0 ) sec cnt(2) count (lba mode only) feature(1) x format track this command writes the desired head and cylinder of the selected drive with a vendor unique data pattern (typically ffh or 00h). to remain host backward compatible, the compactflash storage card expects a sector buffer of data from the host to follow the command with the same protocol as the write sector(s) command al though the information in the buffer is not used by the compactflash storage card. if lba=1 then the number of sectors to format is taken from the seccnt register (0= 256). the use of this command is not recommended. identify drive - ech bit-> 7 6 5 4 3 2 1 0 command(7) ech c/d/h(6) x x x drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) x feature(1) x identify drive the identify drive command enables the host to receive parameter information from the compactflash storage card. this command has the same protocol as the read sector(s) command. the parameter words in the buffe r have the arrangement and meanings defined in table . all reserved bits or words are zero. t able 40 is the definition for each field in the identify drive information. table: identify drive information word address default value total bytes data field type information 0 848ah 2 general configur ation ? signature for the compactflash storage card 1 xxxxh 2 default number of cylinders 2 0000h 2 reserved 3 00xxh 2 default number of heads 4 xxxxh 2 number of unformatted bytes per track 5 xxxxh 2 number of unformatted bytes per sector 6 xxxxh 2 default number of sectors per track 7-8 xxxxh 4 number of sectors per card (word 7 = msw , word 8 = lsw) 9 xxxxh 2 vendor unique
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 22 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) 10-19 aaaa 20 serial number in ascii (right justified ) 20 xxxxh 2 buffer type 21 xxxxh 2 buffer size in 512 byte increments 22 0004h 2 # of ecc bytes passed on read/write long commands 23-26 aaaa 8 firmware revision in ascii. big endian byte order in word 27-46 aaaa 40 model number in ascii (left justified) big endian byte order in word 47 xxxxh 2 maximum number of sectors on read/write mutliple command 48 0000h 2 double word not supported 49 xx00h 2 capabilities 50 0000h 2 reserved 51 0x00h 2 pio data transfer cycle timing mode 52 0000h 2 dma data transfer cycle timing mode 53 0001h 2 translation parameters are valid 54 xxxxh 2 current numbers of cylinders 55 xxxxh 2 current numbers of heads 56 xxxxh 2 current sectors per track 57-58 xxxxh 4 current capacity in sector s(lbas)(word 57 = lsw , word 58 = msw) 59 010xh 2 multiple sector setting 60-61 xxxxh 4 total number of se ctors addressable in lba mode 62-127 0000h 138 reserved 128 xxxxh 2 security status 129-159 0000h 64 vendor unique bytes 160 xxxxh 2 power requirement description 161-255 0000h 170 reserved idle ? 97h or e3h bit-> 7 6 5 4 3 2 1 0 command(7) 97h or e3h c/d/h(6) x drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) timer count (5 mess increments) feature(1) x idle this command causes the compac tflash storage card to set bsy, enter the idle mode, clear bsy and generate an interrupt. if the sector count is non-zero, it is interpreted as a timer count with each count being 5 milliseconds and the autom atic power down mode is enabled. if the se ctor count is zero, the automatic power down mode is disabled. note that this time bas e (5msec) is different from the ata specification.
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 23 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) idle immediate ? 95h or e1h bit-> 7 6 5 4 3 2 1 0 command(7) 95h or e1h c/d/h(6) x drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) x feature(1) x idle immediate this command causes the compac tflash storage card to set bsy, enter the idle mode, clear bsy and generate an interrupt. initialize drive parameters ? 91h bit-> 7 6 5 4 3 2 1 0 command(7) 91h c/d/h(6) x 0 x drive max head(no. of heads-1) cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) number of sectors feature(1) x initialize drive parameters this command enables the host to set the number of sect ors per track and the number of heads per cylinder. only the sector count and the card/drive/head registers are used by this command. read buffer ? e4h bit-> 7 6 5 4 3 2 1 0 command(7) e4h c/d/h(6) x drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) x feature(1) x read buffer the read buffer command enables the host to read the current contents of the compactflash storage card?s sector buffer. this command has t he same protocol as the read sector(s) command.
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 24 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) read multiple ? c4h bit-> 7 6 5 4 3 2 1 0 command(7) c4h c/d/h(6) 1 lba 1 drive head(lba 27 ? 24) cyl high(5) cylinder high (lba 23 ? 16) cyl low(4) cylinder low (15 ? 8) sec num(3) sector number (lba 7 ? 0) sec cnt(2) sector count feature(1) x read multiple the read multiple command performs similarly to t he read sectors command. in terrupts are not generated on every sector, but on the transfer of a block which contains the number of sectors defined by a set multiple command. command execution is identical to the read sectors operation exc ept that the number of sectors defined by a set multiple command are transferred wi thout intervening interrupts. drq qualification of the transfer is required only at the start of t he data block, not on each sector. the block count of sectors to be trans ferred without intervening interrupts is programmed by the set multiple mode command, which must be executed prio r to the read multiple command. when the read multiple command is issued, the sector count regi ster contains the number of sectors (not the number of blocks or the block count) requested. if the num ber of requested sectors is not evenly divisible by the block count, as many full blocks as possible are transferred, followed by a final, partial block transfer. the partial block transfer is for n sectors, where n = remainder (sector count / block count). if the read multiple command is attempted before t he set multiple mode command has been executed or when read multiple commands are disabled, the read multiple operation is reje cted with an aborted command error. disk errors encountered during read multip le commands are posted at the beginni ng of the block or partial block transfer, but drq is still set and the data transfer will take place as it normally would, including transfer of corrupted data, if any interr upts are generated when drq is se t at the beginning of each block or partial block. the error reporting is the same as that on a read sector(s) command. this co mmand reads from 1 to 256 sectors as specified in the sector count register. a sector count of 0 requests 256 sectors.the tr ansfer begins at the sector specified in the sector number register. at command completion, the command block registers c ontain the cylinder, head and sect or number of the last sector read. if an error occurs, the read terminates at the sector where the error occurred. the command block registers contain the cylinder, head and sector number of t he sector where the error occurred. the flawed data is pending in the sector buffer. subsequent blocks or partial blocks are transferred only if the error was a correctable data error. all other errors cause the command to stop after trans fer of the block which contained the error. read long sector ? 22h or 23h bit-> 7 6 5 4 3 2 1 0 command(7) 22h ? 23h c/d/h(6) 1 lba 1 drive head(lba 27 ? 24) cyl high(5) cylinder high (lba 23 ? 16) cyl low(4) cylinder low (15 ? 8) sec num(3) sector number (lba 7 ? 0) sec cnt(2) x feature(1) x read long sector
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 25 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) the read long command performs similarly to the read sect or(s) command except that it returns 516 bytes of data instead of 512 bytes. during a read long command, the compactflash storage card does not check the ecc bytes to determine if there has been a data error. only single sector read long operations are supported. the transfer consists of 512 bytes of data transferred in word mode followed by 4 bytes of ecc data transferred in byte mode. this command has the same pr otocol as the read sector(s) comm and. use of this command is not recommended. read sector(s) ? 20h or 21h bit-> 7 6 5 4 3 2 1 0 command(7) 20h ? 21h c/d/h(6) 1 lba 1 drive head(lba 27 ? 24) cyl high(5) cylinder high (lba 23 ? 16) cyl low(4) cylinder low (15 ? 8) sec num(3) sector number (lba 7 ? 0) sec cnt(2) sector count feature(1) x read sector(s) this command reads from 1 to 256 sectors as specified in the sect or count register. a sect or count of 0 requests 256 sectors. the transfer begins at the sector specified in the sector nu mber register. when this command is issued and after each sector of data (except the last one) has been read by the host, the compactflash storage card sets bsy, puts the sector of data in the buffer, sets drq, clears bsy, and generates an interrupt. the host then reads the 512 bytes of data from the buffer. at command completion, the command block registers c ontain the cylinder, head and sect or number of the last sector read. if an error occurs, the read terminates at the sector where the error occurred. the command block registers contain the cylinder, head, and se ctor number of the sect or where the error occurred. the flawed data is pending in the sector buffer. read verify sector(s) ? 40h or 41h bit-> 7 6 5 4 3 2 1 0 command(7) 40h ? 41h c/d/h(6) 1 lba 1 drive head(lba 27 ? 24) cyl high(5) cylinder high (lba 23 ? 16) cyl low(4) cylinder low (15 ? 8) sec num(3) sector number (lba 7 ? 0) sec cnt(2) sector count feature(1) x read verify sector(s) this command is identical to the r ead sectors command, except that drq is never se t and no data is transferred to the host. when the command is accepted, the compactflash storage card sets bsy. when the requested sectors have been verified, the compactflash storage card clears bsy and generates an interrupt. upon command completion, the command blo ck registers contain the cylinder, head, and sector number of the last sector verified. if an error occurs, the verify terminates at the sector where the error occurs. the command block registers contain the cylinder, head and sector number of the sector where the error o ccurred. the sector count register contains the number of se ctors not yet verified.
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 26 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) recablibrate ? 1xh bit-> 7 6 5 4 3 2 1 0 command(7) 1xh c/d/h(6) 1 lba 1 drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) x feature(1) x recalibrate this command is effectively a nop command to the com pactflash storage card and is provided for compatibility purposes. request sense ? 03h bit-> 7 6 5 4 3 2 1 0 command(7) 03h c/d/h(6) 1 lba 1 drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) x feature(1) x request sense this command requests extended error information for the previous command. table 41 defines the valid extended error codes for the compactflash storage card series product. the extended error code is returned to the host in the error register. extended error codes extended error code description 00h no error detected 01h self test ok ( no error ) 09h miscellaneous error 20h invalid command 21h invalid address ( requested head or sector invalid ) 2fh address overflow ( address too large ) 35h , 36h supply or generated voltage out of tolerance 11h uncorrectable ecc error
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 27 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) 18h corrected ecc error 05h , 30-34h , 37h ,3eh self test or diagnostic failed 10h , 14h id not found 3ah spare sectors exhausted 1fh data transfer error / aborted command 0ch , 38h , 3bh , 3ch , 3fh corrupted media format 03h write / erase failed 22h power level 1 disabled seek ?7x h bit-> 7 6 5 4 3 2 1 0 command(7) 7xh c/d/h(6) 1 lba 1 drive head(lba 27 ? 24) cyl high(5) cylinder high (lba 23 ? 16) cyl low(4) cylinder low (15 ? 8) sec num(3) x (lba 7 ? 0) sec cnt(2) x feature(1) x seek this command is effectively a nop command to the co mpactflash storage card al though it does perform a range check of cylinder and head or lba address and return s an error if the address is out of range. set features - efh bit-> 7 6 5 4 3 2 1 0 command(7) efh c/d/h(6) x drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) configure feature(1) feature set features this command is used by the host to est ablish or select certain features. t able 45 defines all f eatures that are supported.
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 28 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) feature supported feature operation 01h enable 8 ? bit data transfers 0ah enable power level 1 commands 55h disable read look ahead 66h disable power on reset(por) estab lishment of defaults at soft reset 69h nop ? accepted for backward compatibility 81h disable 8 ? bit data transfer 8ah disable power level 1 commands 96h nop ? accepted for backward compatibility 97h accepted for backward compatibility . us e of this feature is not recommended 9ah set the host current source capability. allows tradeoff between current drawn and read/write speed. bbh 4 bytes of data apply on read/write long commands cch enable power on reset (por) estab lishment of defaults at soft reset features 01h and 81h are used to enable and clear 8 bit data transfer modes in true id e mode. if the 01h feature command is issued all data transfers will occur on the low order d7d0 data bus and the iois16 signal will not be asserted for data register accesses. features 0ah and 8ah are used to enable and disable po wer level 1 commands. feature 0ah is the default feature for the compactflash storage card with extended power. features 55h and bbh are the default feat ures for the compactflash storage ca rd; thus, the host does not have to issue this command with these features unless it is necessary for compat ibility reasons. feat ure code 9ah enables the host to configure the card to bes t meet the host system?s power require ments. the host sets a value in the sector count register that is equal to one-fourth of the desired maximum average curr ent (in ma) that the card should consume. for example, if the sector count register is set to 6, the card would be configured to provide the best possible performance without exceeding 24 ma. upon co mpletion of the command, t he card responds to the host with the range of values supported by the card. the minimum value is se t in the cylinder low register, and the maximum value is set in the cylinder hi register. the def ault value, after a power on reset, is to operate at the highest performance and theref ore the highest current mode. the card will accept values outside this programmable range, but w ill operate either at the lowest power or highest performance as appropriate. features 66h and cch can be used to enabl e and disable whether the power on reset (por) defaults will be set when a soft reset occurs. the default setting is to revert to the por defaults when a soft reset occurs. set multiple mode ? c6h bit-> 7 6 5 4 3 2 1 0 command(7) c6h c/d/h(6) x drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) sector count feature(1) x set multiple mode
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 29 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) this command enables the compactflash storage card to perform read and write multiple operations and establishes the block count for these commands. the sector count regist er is loaded with the number of sectors per block. upon receipt of the comm and, the compactflash storage card sets bsy to 1 and checks the sector count register. if the sector count register contains a valid value and the block count is supported, the value is loaded for all subsequent read multiple and write mult iple commands and execution of t hose commands is enabled. if a block count is not supported, an aborted command error is posted, and read multiple and wr ite multiple commands are disabled. if the sector count regi ster contains 0 when the command is issued, read and write multiple commands are disabled. at power on, or after a hardware or (unless disabled by a set feature command) software reset, the default mode is read and write multiple disabled. set sleep mode ? 99h or e6h bit-> 7 6 5 4 3 2 1 0 command(7) 99h or e6h c/d/h(6) x drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) x feature(1) x set sleep mode this command causes the compactflash storage card to set bsy, enter the sl eep mode, clear bsy and generate an interrupt. recovery from sleep mode is accomplished by simply issuing another command (a reset is permitted but not required). sleep mode is also entered when internal timer expires so the host does not need to issue this command except when it wishes to enter sleep mode immediately. the def ault value for the timer is 1.6 milliseconds. note that this time base (1.6 msec ) is different from the ata specification. standby ? 96h or e2h bit-> 7 6 5 4 3 2 1 0 command(7) 96h or e2h c/d/h(6) x drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) x feature(1) x standby this command causes the compactfla sh storage card to set bsy, enter the sleep mode (which corresponds to the ata ?standby? mode), clear bsy and re turn the interrupt immediately. recovery from sleep mode is accomplished by simply issuing another command (a reset is not required).
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 30 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) standby immediate ? 94h or e0h bit-> 7 6 5 4 3 2 1 0 command(7) 94h or e0h c/d/h(6) x drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) x feature(1) x standby immediate this command causes the compactfla sh storage card to set bsy, enter the sleep mode (which corresponds to the ata ?standby? mode), clear bsy and re turn the interrupt immediately. recovery from sleep mode is accomplished by simply issuing another command (a reset is not required). translate sector ? 87h bit-> 7 6 5 4 3 2 1 0 command(7) 87h c/d/h(6) 1 lba 1 drive head(lba 27 ? 24) cyl high(5) cylinder high (lba 23 ? 16) cyl low(4) cylinder low (15 ? 8) sec num(3) sector number (lba 7 ? 0) sec cnt(2) x feature(1) x translate sector this command allows the host a method of determining t he exact number of times a user sector has been erased and programmed. the controller responds with a 512 byte buffer of information containing the desired cylinder, head and sector, including its logical addre ss, and the hot count, if available, for that sector. table 46 represents the information in the buffer. pleas e note that this command is unique to the compactflash storage card. address information address information 00h ? 01h cylinder msb (00), cylinder lsb (01) 02h head 03h sector 04h ? 06h lba msb (04) ? lsb (06) 07h ? 12h reserved 13h erased flag (ffh) = erased; 00h = not erased 14h ? 17h reserved 18h ? 1ah hot count msb (18) ? lsb (1a)
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 31 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) 1bh ? 1ffh reserved note 1: a value of 0 indicates hot count is not supported. wear level ? f5h bit-> 7 6 5 4 3 2 1 0 command(7) f5h c/d/h(6) x x x drive flag cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) completion status feature(1) x wear level for the compactflash storage cards that do not support security mode feature set, this command is effectively a nop command and only implement ed for backward compatibility. the sector count register will always be returned with a 00h indicating w ear level is not needed. if the compactflash storage card supports security mode feature set, this co mmand shall be handled as security freeze lock. write buffer ? e8h bit-> 7 6 5 4 3 2 1 0 command(7) e8h c/d/h(6) x drive x cyl high(5) x cyl low(4) x sec num(3) x sec cnt(2) x feature(1) x write buffer the write buffer command enables the host to overwrite c ontents of the compactflash storage card?s sector buffer with any data pattern desired. this command has the same protocol as t he write sector(s) command and transfers 512 bytes. write long sector ?32h or 33h bit-> 7 6 5 4 3 2 1 0 command(7) 32h or 33h c/d/h(6) 1 lba 1 drive head(lba 27 ? 24) cyl high(5) cylinder high (lba 23 ? 16) cyl low(4) cylinder low (15 ? 8) sec num(3) sector number (lba 7 ? 0)
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 32 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) sec cnt(2) x feature(1) x write long sector this command is similar to the write sector(s) command exc ept that it writes 516 byte s instead of 512 bytes. only single sector write long operations are supported. the transfer consists of 512 bytes of data transferred in word mode followed by 4 bytes of ecc transferred in byte mode. because of the unique nature of the solid-state compactflash storage card, the four bytes of ecc tr ansferred by the host may be used by the compactflash storage card. the compactflash storage card may discard these four bytes and write t he sector with valid ecc data. this command has the same pr otocol as the write sector(s) co mmand. use of this command is not recommended. write multiple command ? c5h bit-> 7 6 5 4 3 2 1 0 command(7) c5h c/d/h(6) x lba x drive head cyl high(5) cylinder high cyl low(4) cylinder low sec num(3) sector number sec cnt(2) sector count feature(1) x write multiple command note : the current revision of the compactflash storage card only supports a block count of 1 as indicated in the identify drive command information. this command is provided for compatibility with future products which may support a larger block count. this command is similar to the write sectors command. the compactflash storage card sets bsy within 400 nsec of accepting the command. inte rrupts are not presented on each sector but on the tr ansfer of a block which contains the number of sect ors defined by set multiple. command execution is identical to the write sectors operation ex cept that the number of sectors defined by the set multiple command is transferr ed without intervening interrupts. drq qualification of the transfer is required only at the start of the data block, not on each sector. the block count of sectors to be transferred without intervening interr upts is programmed by the set multiple mode command, which must be executed prior to the write multiple command. when the write multiple command is iss ued, the sector count regi ster contains the number of sectors (not the number of blocks or the block count) requested. if the num ber of requested sectors is not evenly divisible by the sector/block, as many full blocks as possible are transferred, followed by a final, partial block transfer. the partial block transfer is for n sectors, where: n = remainder ( sector count / block count ). if the writ e multiple command is attemp ted before the set multiple mode command has been executed or when wr ite multiple commands are disabl ed, the write mu ltiple operation will be rejected with an aborted command error. errors encountered during write multiple commands are posted after the attempt ed writes of the block or partial block transferred. the write command ends with the sector in error, even if it is in the middle of a block. subsequent blocks are not transferred in the event of an error. interrupts are generated when drq is set at the beginning of each block or partial block. the command block registers contain the cylinder, head and sector number of the sector where the error occurred and the sector count register contains the residual number of se ctors that need to be transferred for successful completion of the command, e.g., each block has 4 sectors, a request fo r 8 sectors is issued and an error occurs on the third sector. the se ctor count register cont ains 6 and the address is t hat of the third sector. write multiple without erase ? cdh bit-> 7 6 5 4 3 2 1 0 command(7) cdh c/d/h(6) x lba x drive head
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 33 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) cyl high(5) cylinder high cyl low(4) cylinder low sec num(3) sector number sec cnt(2) sector count feature(1) x write multiple without erase this command is similar to the write multiple command with the exception that an implied erase before write operation is not performed. the sect ors should be pre-erased with the er ase sector(s) command before this command is issued. write sector(s) ? 30h or 31h bit-> 7 6 5 4 3 2 1 0 command(7) 30h or 31h c/d/h(6) 1 lba 1 drive head(lba 27 ? 24) cyl high(5) cylinder high (lba 23 ? 16) cyl low(4) cylinder low (15 ? 8) sec num(3) sector number (lba 7 ? 0) sec cnt(2) sector count feature(1) x write sector(s) this command writes from 1 to 256 sect ors as specified in the sector count register. a sector count of zero requests 256 sectors. the transfer begins at the sector specif ied in the sector number register. when this command is accepted, the compactflash st orage card sets bsy,then sets drq and clears bsy, then waits for the host to fill the sector buffer with the data to be written. no interrupt is generated to start the first host transfer operati on. no data should be transferred by the host until bsy has been cleared by the host. for multiple sectors, after the first sector of data is in the buffer, bsy w ill be set and drq will be cleared. after the next buffer is ready for data, bsy is cleared, drq is se t and an interrupt is generated. when the final sector of data is transferred, bsy is set and drq is cleared. it will re main in this state until t he command is completed at which time bsy is cleared and an interrupt is generated. if an error occurs during a write of more than one sector, wr iting terminates at the sect or where the error occurs. the command block registers contain the cylinder, head and sector number of the sector where the error occurred. the host may then read the command block to det erminem what error has occurred, and on which sector. write sector(s) without erase ? 38h bit-> 7 6 5 4 3 2 1 0 command(7) 38h c/d/h(6) 1 lba 1 drive head(lba 27 ? 24) cyl high(5) cylinder high (lba 23 ? 16) cyl low(4) lba(15 ? 8) sec num(3) sector number (lba 7 ? 0) sec cnt(2) sector count feature(1) x
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 34 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) write sector(s) without erase this command is similar to the write sector(s) command with the exception that an implied erase before write operation is not performed. this comm and has the same protocol as the wr ite sector(s) command. the sectors should be pre-erased with the erase se ctor(s) command before this command is issued. if the sector is not pre- erased with the erase sector(s) command, a normal write sector operation will occur. write verify ? 3ch bit-> 7 6 5 4 3 2 1 0 command(7) 3ch c/d/h(6) 1 lba 1 drive head(lba 27 ? 24) cyl high(5) cylinder high (lba 23 ? 16) cyl low(4) lba(15 ? 8) sec num(3) sector number (lba 7 ? 0) sec cnt(2) sector count feature(1) x write verify this command is similar to the write sector(s) command, except each sector is verified immediately after being written. this command has the same prot ocol as the write sector(s) command. summaries of the valid status and error value for all the ata command set error and status register error register status register command bbk unc idnf abrt amnf drdy dwf dsc corr err checkpowermode v v v v v executedrivediagnostic v v v v erase sector(s) v v v v v v format track v v v v v v identify drive v v v v v idle v v v v v idle immediate v v v v v initializedriveparameter v v v read buffer v v v v v read multiple v v v v v v v v v read long sector v v v v v v v read sector(s) v v v v v v v v v read verify sectors v v v v v v v v v recalibrate v v v v v request sense v v v v v seek v v v v v
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 35 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) set features v v v v v set multiple mode v v v v v set sleep mode v v v v v stand by v v v v v stand by immediate v v v v v translate sector v v v v v v wear level v v v v v v v v write buffer v v v v v write long sector v v v v v v write multiple v v v v v v v write multiple w/o erase v v v v v v v write sector(s) v v v v v v v write sector(s) w/o erase v v v v v v v write verify sector(s) v v v v v v v invalid command code v v v v v v = valid on this command
hanbit hfdom40s6vxxx url:www.hbe.co.kr - 36 - hanbit electronics co., ltd. rev. 1.1 (august, 2005) ordering infomation no parts capacity media transfer mode operation mode 1 dom40s6v128 128mbyte byte true ide 2 dom40s6v256 256mbyte byte true ide 3 dom40s6v384 384mbyte byte true ide 4 dom40s6v512 512mbyte byte true ide 5 dom40s6v640 640mbyte byte true ide 6 dom40s6v768 768mbyte byte true ide 7 dom40s6v1g 1gbyte byte true ide 8 dom40s6v1.5g 1.5gbyte byte true ide 9 dom40s6v2g 2gbyte byte true ide 10 dom40s6v3g 3gbyte byte true ide

▲Up To Search▲

Price & Availability of DOM40S6V15G

	To Download DOM40S6V15G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .